doublegunshop.com - home Forums General Discussion DoubleGun BBS @ doublegunshop.com Making Turnscrews

May
S	M	T	W	T	F	S
			1	2	3	4
5	6	7	8	9	10	11
12	13	14	15	16	17	18
19	20	21	22	23	24	25
26	27	28	29	30	31

Who's Online Now

4 members (Argo44, coosa, Tamid, 1 invisible), 605 guests, and 3 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums10

Topics38,541

Posts546,043

Members14,420

Most Online1,344
Apr 29th, 2024

Print Thread

Making Turnscrews #570748 04/28/20 08:21 AM
Joined: Jan 2002 Posts: 39 South Carolina Yallarhammer OP Sidelock
OP Yallarhammer Sidelock Joined: Jan 2002 Posts: 39 South Carolina	I need to make some very thin tip turnscrews. I have the Brownells thin bit magantip set and they are too thick. Would you recommend grinding those down or start with something different?

Entire Thread
Subject	Posted By	Posted
Making Turnscrews	Yallarhammer	04/28/20 12:21 PM
Re: Making Turnscrews	RARiddell	04/28/20 12:27 PM
Re: Making Turnscrews	bill schodlatz	04/28/20 02:40 PM
Re: Making Turnscrews	James Flynn	04/28/20 04:18 PM
Re: Making Turnscrews	bushveld	04/28/20 08:49 PM
Re: Making Turnscrews	ClapperZapper	04/28/20 08:28 PM
Re: Making Turnscrews	Yallarhammer	04/28/20 10:32 PM
Re: Making Turnscrews	Karl Graebner	04/28/20 10:36 PM
Re: Making Turnscrews	Rocketman	04/29/20 02:38 AM
Re: Making Turnscrews	ClapperZapper	04/29/20 12:39 PM
Re: Making Turnscrews	Woodreaux	04/29/20 07:21 PM
Re: Making Turnscrews	Stanton Hillis	04/29/20 11:07 PM
Re: Making Turnscrews	ClapperZapper	04/29/20 11:53 PM
Re: Making Turnscrews	Mike Rowe	05/03/20 01:20 PM
Re: Making Turnscrews	Stanton Hillis	05/03/20 01:29 PM
Re: Making Turnscrews	Mark Larson	05/03/20 05:03 PM
Re: Making Turnscrews	Stanton Hillis	05/03/20 05:26 PM
Re: Making Turnscrews	SKB	05/03/20 05:28 PM
Re: Making Turnscrews	Rick W	05/03/20 06:43 PM
Re: Making Turnscrews	FlyChamps	05/03/20 11:08 PM
Re: Making Turnscrews	Stanton Hillis	05/03/20 11:25 PM
Re: Making Turnscrews	Doug Mann	05/04/20 01:37 PM
Re: Making Turnscrews	Der Ami	05/04/20 09:08 PM
Re: Making Turnscrews	Stanton Hillis	05/05/20 12:25 AM
Re: Making Turnscrews	Der Ami	05/05/20 12:39 PM
Re: Making Turnscrews	James Flynn	05/05/20 07:26 PM
Re: Making Turnscrews	gil russell	05/06/20 11:06 PM

Link Copied to Clipboard

Updated every minute of everyday!

Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 0.393s Queries: 16 (0.372s) Memory: 0.8452 MB (Peak: 1.9024 MB) Data Comp: Off Server Time: 2024-05-18 18:56:23 UTC
Valid HTML 5 and Valid CSS