S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums10
Topics38,443
Posts544,800
Members14,405
|
Most Online1,258 Mar 29th, 2024
|
|
|
Joined: Mar 2021
Posts: 62 Likes: 9
Sidelock
|
OP
Sidelock
Joined: Mar 2021
Posts: 62 Likes: 9 |
|
|
|
|
Joined: Oct 2016
Posts: 284 Likes: 25
Sidelock
|
Sidelock
Joined: Oct 2016
Posts: 284 Likes: 25 |
The shotgun barrels was chambered for 16 gauge 2 9/16" shells and the rifle, based on what I can make out of the bore marking 118/35? is most likely a 9.3x72R.
|
1 member likes this:
journeymen |
|
|
|
Joined: Mar 2021
Posts: 62 Likes: 9
Sidelock
|
OP
Sidelock
Joined: Mar 2021
Posts: 62 Likes: 9 |
is there any easy way to find out around what time it was made? I downloaded the proof stamp log that i found posted here but its a little blurry
|
|
|
|
Joined: Aug 2007
Posts: 10,775 Likes: 183
Sidelock
|
Sidelock
Joined: Aug 2007
Posts: 10,775 Likes: 183 |
Well, I do not see the term >>Nitro<< stamped anywhere so it would date between 1893 & 1912. I have seen that barrel stamp of >>RJ<< surmounted by a Crown on the lower rifled tube. I'll have to search. What stamps are on the frame?
Serbus,
Raimey rse
|
|
|
|
Joined: Aug 2007
Posts: 10,775 Likes: 183
Sidelock
|
Sidelock
Joined: Aug 2007
Posts: 10,775 Likes: 183 |
Too, the initials >>RW<< higher on the lower tube may point to a mechanic.
Serbus,
Raimey rse
|
|
|
|
Joined: Jul 2012
Posts: 4,461 Likes: 207
Sidelock
|
Sidelock
Joined: Jul 2012
Posts: 4,461 Likes: 207 |
Journeyman, The crown W on the barrels shows were choked, but the amount of constriction is not shown. Since it has been re-blued and it is unknown what process was used, suggest you keep a close watch for rib loosening, in case it was hot salts blued. Mike
|
|
|
|
Joined: Mar 2021
Posts: 62 Likes: 9
Sidelock
|
OP
Sidelock
Joined: Mar 2021
Posts: 62 Likes: 9 |
My apologies, Journeyman, The crown W on the barrels shows were choked, but the amount of constriction is not shown. Since it has been re-blued and it is unknown what process was used, suggest you keep a close watch for rib loosening, in case it was hot salts blued. Mike I didn't even consider that, thank you for the heads up
|
|
|
|
Joined: Mar 2021
Posts: 62 Likes: 9
Sidelock
|
OP
Sidelock
Joined: Mar 2021
Posts: 62 Likes: 9 |
I tried to get a better one of the rifle barrel stamps
Last edited by journeymen; 03/19/21 08:27 AM.
|
|
|
|
Joined: Jul 2012
Posts: 4,461 Likes: 207
Sidelock
|
Sidelock
Joined: Jul 2012
Posts: 4,461 Likes: 207 |
The crown G means it was proofed for a single projectile. The 118/35 is the bore( not groove or bullet) diameter, expressed in gauge measurement. This works out to about 8.64mm or about .341". Experience shows that barrels with this marking commonly "slug" to .357-359" groove diameter. The most common chambering with this mark seems to be one of the 9.3x72R cartridges, but sometimes it may be found on one of the other case length 9.3 cartridges( 70-82mm) or some 9mm cartridges such as 9x58 1/2R S&S. The best way to determine the chambering is by making a chamber cast. If it were mine, I would try a 9.3x72R normal. before making a chamber cast, however. Mike
|
|
|
|
Joined: Mar 2021
Posts: 62 Likes: 9
Sidelock
|
OP
Sidelock
Joined: Mar 2021
Posts: 62 Likes: 9 |
How do I learn to read these markings? Is there a guide i can reference?
|
|
|
|
|