S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums10
Topics38,503
Posts545,538
Members14,414
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Dec 2001
Posts: 3,964 Likes: 89
Sidelock
|
OP
Sidelock
Joined: Dec 2001
Posts: 3,964 Likes: 89 |
I have usually used a very light application of grease on the hooks of my doubles but I am aware grease is a dirt magnet. I am considering changing to a light coating of oil on the wear points. Main concern I have is oil tends to wick upwards to the head of the stock, even light coatings. (I store my guns muzzle down). What say you?
When an old man dies a library burns to the ground. (Old African proverb)
|
|
|
|
Joined: May 2016
Posts: 1,417 Likes: 197
Sidelock
|
Sidelock
Joined: May 2016
Posts: 1,417 Likes: 197 |
Grease for me, a thorough cleaning after my outing. Karl
|
|
|
|
Joined: Mar 2011
Posts: 2,983 Likes: 106
Sidelock
|
Sidelock
Joined: Mar 2011
Posts: 2,983 Likes: 106 |
I use Tri-Flow, but have used grease too. Grease is more messy imho. Seems I never have a q-tip when I apply grease, so use my finger and have to wipe it off somewhere, and thats usually on my pants since I usually dont have a paper towel or rag handy either. Tri-flow is better and easier for the unprepared.
Socialism is almost the worst.
|
|
|
|
Joined: May 2004
Posts: 778 Likes: 36
Sidelock
|
Sidelock
Joined: May 2004
Posts: 778 Likes: 36 |
I use a 50/50 mix of good quality automotive grease mixed with a light oil like 3 in 1. Wipe off each time the gun has been used and reapply sparingly.
|
|
|
|
Joined: Feb 2006
Posts: 3,735 Likes: 53
Sidelock
|
Sidelock
Joined: Feb 2006
Posts: 3,735 Likes: 53 |
Molycote by Dow Corning a graphite, does not attract dirt like grease or oil.
David
|
|
|
|
Joined: Feb 2003
Posts: 4,038 Likes: 48
Sidelock
|
Sidelock
Joined: Feb 2003
Posts: 4,038 Likes: 48 |
If a lube won't stay where you put it, there's no lube at all.
The part about grease attracting dirt and oil not doing so is a myth in my opinion.
I use grease on hinge pins, bifurctaed lumps, and bolts.
My mix is Mobil 1 synthetic grease mixed 3-1 with Permatex engine assembly lube. The tackifier in the assembly lube makes the mix stick to the parts like glue.
It's replaced after each use.
"The price of good shotgunnery is constant practice" - Fred Kimble
|
|
|
|
Joined: Jan 2002
Posts: 13,162 Likes: 1155
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 13,162 Likes: 1155 |
Grease on hinge pins, knuckle/forend iron joint, and bolts. I've seen galling on the knuckle from poor lubrication, and I don't trust oil there.
SRH
Last edited by Stan; 08/28/20 05:10 PM. Reason: correcting spell check
May God bless America and those who defend her.
|
|
|
|
Joined: Jan 2002
Posts: 9,758 Likes: 748
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 9,758 Likes: 748 |
Either version of Mobile Synthetic. Knuckle, pin, lumps. Clean after use and repeat.
Best, Ted
|
|
|
|
Joined: Feb 2003
Posts: 4,038 Likes: 48
Sidelock
|
Sidelock
Joined: Feb 2003
Posts: 4,038 Likes: 48 |
I've seen galling on the knuckle from poor lubrication, and I don't trust oil there.
SRH Likewise. I saw one of the FN made 'Winchester' O/U's gall in that spot.
"The price of good shotgunnery is constant practice" - Fred Kimble
|
|
|
|
Joined: Jan 2002
Posts: 13,162 Likes: 1155
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 13,162 Likes: 1155 |
The one I saw was actually an old MX8. Shameful.
Didn't realize spellcheck had screwed up "galling". I corrected it.
Best, SRH
May God bless America and those who defend her.
|
|
|
|
|