|
S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums10
Topics38,496
Posts545,393
Members14,412
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Jan 2002
Posts: 5,090 Likes: 36
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 5,090 Likes: 36 |
Taking this 12ga Ejector apart for cleaning but not sure what type of action this is. Coil springs in action, triggers attached to bottom plate. And is that an H&H ejector system? It's a 1953 JP Sauer. thanks, Rob
My problem lies in reconciling my gross habits with my net income. - Errol Flynn
|
|
|
|
Joined: Jan 2011
Posts: 246 Likes: 2
Sidelock
|
Sidelock
Joined: Jan 2011
Posts: 246 Likes: 2 |
These are Ernst Kerner's, Suhl, improved Anson and Deeley boxlock. By hanging the coil spring powered sear levers from the top of the action Kerner moved the sear notch as far away from the hammer's fulcrum, markedly reducing the pressure the cocked mainspring applies to the sear engagement, making for a lighter but safer trigger pull. During the 1930s Kerner's boxlock became the Suhl industry standard. The ejectors are of the Southgate override type, as are the so called Holland & Holland ones.
|
|
|
|
Joined: Jan 2002
Posts: 5,090 Likes: 36
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 5,090 Likes: 36 |
Thanks Kudae,
so how does one begin to disassemble them and clean them up?
My problem lies in reconciling my gross habits with my net income. - Errol Flynn
|
|
|
|
Joined: Apr 2008
Posts: 173
Sidelock
|
Sidelock
Joined: Apr 2008
Posts: 173 |
Why do you need to disassenbly the action ? I have always soaked it in whole peace to car motor washing detergent, let it stay there some time and after that washed it again with alcohol or acetone. At last, of course very thin oil thoroughly.
|
|
|
|
Joined: Jan 2011
Posts: 246 Likes: 2
Sidelock
|
Sidelock
Joined: Jan 2011
Posts: 246 Likes: 2 |
Igorrock is right here! Disassembling any Anson&Deeley type boxlock action is quite easy, but putting it back together is not as easy as "reverse order"! Gunsmithes use a special key to put back the maisprings and hammers into the action bar. Without such key and the knowledge how to use it, it is very difficult to compress the mainsprings and hammers and insert the screws holding everything together at the same time, unless you have three hands with eight fingers on each one. Trying to do so without the proper tools and knowledge results in scratched up parts. So I usually stay away from taking out hammers and mainsprings if it is not absolutely necessary because something has to be replaced/repaired.
|
|
|
|
Joined: Feb 2008
Posts: 1,119 Likes: 27
Sidelock
|
Sidelock
Joined: Feb 2008
Posts: 1,119 Likes: 27 |
I usually have gummy actions cleaned in an aqueous ultrasonic bath, followed by WD 40, allowed to dry, then light machine oil. The only disassembly is the bottom plate and the buttstock .
|
|
|
|
Joined: Jan 2002
Posts: 5,090 Likes: 36
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 5,090 Likes: 36 |
Done! cleaned in the ultrasonic with some Simple Green, rinsed in boiling water, blown dry, soaked in some Brownells Water Displacing Oil, sprayed with CRP, blown out again, a little gun grease on the appropriate surfaces and back together for the duck opener this morning.
Right now stored muzzle down but this week will take apart again and seal the head stock.
Thanks gents.
My problem lies in reconciling my gross habits with my net income. - Errol Flynn
|
|
|
|
|
|