|
S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums10
Topics38,445
Posts544,824
Members14,406
|
Most Online1,258 Mar 29th, 2024
|
|
|
Joined: Jan 2002
Posts: 7,701 Likes: 99
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,701 Likes: 99 |
I have bought a project gun. A Boss&Co hammergun from about 1871. I have not even seen it yet, except for pictures posted by the seller in the 'for sale' forum here.
I've never renovated anything and can barely turn a screw. I did however buy a copy of Tony Treadwell's book and must have caught something from reading it!
Foremost, I realize I'm going to need a suitable set of 30" Damascus barrels to have sleeved onto the "decommissioned" set that is on the gun now. I see no point in sleeving modern steel onto this gun. Anyone have a donor set of suitable fine Damascus available for purchase?...Geo
|
|
|
|
Joined: Dec 2001
Posts: 3,573 Likes: 80
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 3,573 Likes: 80 |
John his boss has holes in it ground in when sold. I've seen a few sets of damascus barrels on ebay real cheap. The problem is the damascus patterns won't match and you need a good set of donor barrels. i.e. wall thickness and pitless. I salute you for trying to do the damascus route. Good luck.
|
|
|
|
Joined: Jan 2006
Posts: 15,456 Likes: 86
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 15,456 Likes: 86 |
Should have stayed out of that Georgia peach wine...
|
|
|
|
Joined: Dec 2010
Posts: 691 Likes: 7
Sidelock
|
Sidelock
Joined: Dec 2010
Posts: 691 Likes: 7 |
Keith Kearcher has sleeved damascus with damascus.
Wild Skies Since 1951
|
|
|
|
Joined: Oct 2006
Posts: 1,544
Sidelock
|
Sidelock
Joined: Oct 2006
Posts: 1,544 |
Forget about barrel lining. Sleeving old damascus barrels to old damascus breech ends - now there is a project. Good luck.
|
|
|
|
Joined: Jun 2008
Posts: 2,736 Likes: 96
Sidelock
|
Sidelock
Joined: Jun 2008
Posts: 2,736 Likes: 96 |
It will be hard not to see the join. I think Peter Dyson in England still has some tubes but they are going to be expensive. I would say the best to to sleeve with steel and with the money you will save go out an buy another Boss hammer gun. Lagopus.....
|
|
|
|
Joined: Jan 2002
Posts: 1,393
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 1,393 |
Teague barrel lining is no longer avaiable, so I understood. Is someone else doing it?
|
|
|
|
Joined: Jan 2002
Posts: 7,701 Likes: 99
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,701 Likes: 99 |
Teague lining wouldn't have worked with these barrels anyway; there's about a one inch square of barrel sawn out of each one, albeit above where the cut for the "chamber block" would be made...Geo
|
|
|
|
Joined: Jan 2002
Posts: 7,701 Likes: 99
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,701 Likes: 99 |
Should have stayed out of that Georgia peach wine... Georgia peach wine had nothing to do with this undertaking, but I can't argue with jOe's opinion of my "project". Even before Tony Treadwell poisoned my mind with his book, I'd always wanted to bring a good one back from the Cracker Barrell wall of shame...Geo
|
|
|
|
|
|