|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
|
Forums10
Topics38,527
Posts545,850
Members14,420
| |
Most Online1,344
Apr 29th, 2024
|
|
|
|
Joined: Jan 2006
Posts: 15,456 Likes: 86
Sidelock
|
OP
Sidelock
Joined: Jan 2006
Posts: 15,456 Likes: 86 |
I've got a couple of old 10 hammer guns both have been reproofed for Nitro...4 tons pressure and 1 & 1/2oz. of shot and marked 3 & 1/2".
One is Damascus the othere is Fluid/sleeved.
Both are in top condition and might hold up to a modern 10 shell but I'd rather not take the chance on wrecking something.
I've been shooting black powder in the one and I may just continue to do so...but in the Fluid steel gun I'd like to shoot some low pressure Nitro with good velosity to be used hunting.
I tried a search on here and came up emty handed.
Thanks
|
|
|
|
|
Joined: Apr 2005
Posts: 1,126 Likes: 94
Sidelock
|
|
Sidelock
Joined: Apr 2005
Posts: 1,126 Likes: 94 |
|
|
|
|
|
Joined: Jan 2006
Posts: 15,456 Likes: 86
Sidelock
|
|
OP
Sidelock
Joined: Jan 2006
Posts: 15,456 Likes: 86 |
I'm looking for a recipe for Federal hulls....low pressure with good velosity 1 & 5/8oz lead.
|
|
|
|
|
Joined: Apr 2005
Posts: 1,126 Likes: 94
Sidelock
|
|
Sidelock
Joined: Apr 2005
Posts: 1,126 Likes: 94 |
Sorry, I didn't understand. Could you start with a LP 12 gauge load and "work" into it?
|
|
|
|
|
Joined: Aug 2005
Posts: 87
Sidelock
|
|
Sidelock
Joined: Aug 2005
Posts: 87 |
Federal hull thimed to 2 7/8"
30 gr IMR 7625
1 16 ga 1/4" filler wad inside plastic wad
WW 209 primer
Remington SP 10 wad
1 1/8 oz shot
six point crimp
1129 fps
4800 psi
Fed hull 2 7/8"
35 gr IMR 4756
WW 209
1 16 gauge .070 nitro card inside plactic wad
1 1/4 oz shot
six point crimp
1194 fps
5800 psi
SP 10 wad
Good shooting, Harry
|
|
|
|
|
Joined: Jan 2002
Posts: 2,522
Sidelock
|
|
Sidelock
Joined: Jan 2002
Posts: 2,522 |
Homeless, email me so I have your email address. That way I can send you a file with all you need.
|
|
|
|
|
Joined: Jan 2006
Posts: 15,456 Likes: 86
Sidelock
|
|
OP
Sidelock
Joined: Jan 2006
Posts: 15,456 Likes: 86 |
Thanks Harry I'm looking for a heavier load than that. PM sent Jerry.
|
|
|
|
|
Joined: Aug 2005
Posts: 87
Sidelock
|
|
Sidelock
Joined: Aug 2005
Posts: 87 |
Federal Hull 2 7/8"
WW 209
35 grains IMR 4756
X10X wad
2 x 1/4" fillers
Mylar shot wrap
.028 over shot card
Roll Crimp
1153 fps
7000 psi
All of these loads are from Sherman Bell.
Harry
|
|
|
|
|
Joined: Aug 2005
Posts: 87
Sidelock
|
|
Sidelock
Joined: Aug 2005
Posts: 87 |
The above load is for 1 5/8 oz lead shot.
Harry
|
|
|
|
|
Joined: Jan 2006
Posts: 15,456 Likes: 86
Sidelock
|
|
OP
Sidelock
Joined: Jan 2006
Posts: 15,456 Likes: 86 |
Thanks Harry....How could I adapt that load to a 3 & 1/2" Federal hull without fear of raising the pressure too much ?
|
|
|
|
|
|
|
