doublegunshop.com - home Forums General Discussion DoubleGun BBS @ doublegunshop.com Making Turnscrews

October
S	M	T	W	T	F	S
			1	2	3	4
5	6	7	8	9	10	11
12	13	14	15	16	17	18
19	20	21	22	23	24	25
26	27	28	29	30	31

Who's Online Now

3 members (SKB, John E, 1 invisible), 783 guests, and 3 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums10

Topics39,514

Posts562,221

Members14,590

Most Online9,918
Jul 28th, 2025

Print Thread

Re: Making Turnscrews Yallarhammer #571003 04/29/20 07:53 PM
Joined: Jun 2006 Posts: 3,245 Likes: 423 Great Lakes region ClapperZapper Sidelock
ClapperZapper Sidelock Joined: Jun 2006 Posts: 3,245 Likes: 423 Great Lakes region	Replacement screws are a cottage industry. Must be a reason. If I want to remove a screw, I'm going to measure the slot, and pick a bit that fits the slot. Maybe belt sand one a touch thinner. I'm not going to buy Taconite pellets. It's about removing a screw without messing up the slot. Out there doing it best I can.

Entire Thread
Subject	Posted By	Posted
Making Turnscrews	Yallarhammer	04/28/20 12:21 PM
Re: Making Turnscrews	RARiddell	04/28/20 12:27 PM
Re: Making Turnscrews	bill schodlatz	04/28/20 02:40 PM
Re: Making Turnscrews	James Flynn	04/28/20 04:18 PM
Re: Making Turnscrews	bushveld	04/28/20 08:49 PM
Re: Making Turnscrews	ClapperZapper	04/28/20 08:28 PM
Re: Making Turnscrews	Yallarhammer	04/28/20 10:32 PM
Re: Making Turnscrews	Karl Graebner	04/28/20 10:36 PM
Re: Making Turnscrews	Rocketman	04/29/20 02:38 AM
Re: Making Turnscrews	ClapperZapper	04/29/20 12:39 PM
Re: Making Turnscrews	Woodreaux	04/29/20 07:21 PM
Re: Making Turnscrews	Stanton Hillis	04/29/20 11:07 PM
Re: Making Turnscrews	ClapperZapper	04/29/20 11:53 PM
Re: Making Turnscrews	Mike Rowe	05/03/20 01:20 PM
Re: Making Turnscrews	Stanton Hillis	05/03/20 01:29 PM
Re: Making Turnscrews	Mark Larson	05/03/20 05:03 PM
Re: Making Turnscrews	Stanton Hillis	05/03/20 05:26 PM
Re: Making Turnscrews	SKB	05/03/20 05:28 PM
Re: Making Turnscrews	Rick W	05/03/20 06:43 PM
Re: Making Turnscrews	FlyChamps	05/03/20 11:08 PM
Re: Making Turnscrews	Stanton Hillis	05/03/20 11:25 PM
Re: Making Turnscrews	Doug Mann	05/04/20 01:37 PM
Re: Making Turnscrews	Der Ami	05/04/20 09:08 PM
Re: Making Turnscrews	Stanton Hillis	05/05/20 12:25 AM
Re: Making Turnscrews	Der Ami	05/05/20 12:39 PM
Re: Making Turnscrews	James Flynn	05/05/20 07:26 PM
Re: Making Turnscrews	gil russell	05/06/20 11:06 PM

Link Copied to Clipboard

Updated every minute of everyday!

Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 5.292s Queries: 17 (0.524s) Memory: 0.8457 MB (Peak: 1.9025 MB) Data Comp: Off Server Time: 2025-10-14 19:08:04 UTC
Valid HTML 5 and Valid CSS