|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
|
2 members (Edm1, Reidy),
266
guests, and
12
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,572
Posts546,459
Members14,424
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Dec 2005
Posts: 211
Member
|
OP
Member
Joined: Dec 2005
Posts: 211 |
I have a set of damascus barrels that have a very nice deep etch. The barrels are in very good shape and the bores are a bit dark but don't appear to have any deep pitting. They do however, have straight rifleing in both barrels. I plane to breech these barrels for use on a sxs flintlock but am concerned about the deep etch. When I fit breech plugs I usualy file the plugs down to the barrel size and often go a bit more to reduce the chamber flair. If I do this, how can I reinstate the deep etch to the pattern to match the balance of the barrels?? I don't really want to remove the entire pattern. I could fit the breeches without touching the barrels I suppose but a good transition would be difficult to achieve (but possible). Also, is there any reason, other than novelty, to leave the straight rifleing in the barrels?. If i ream the rifleing out I can clean up the bores to like new (but the straight rifleing is kinda funky and you don't see it everyday). Thoughts.
Tact is for those not clever enough to be sarcastic
|
|
|
|
Joined: May 2006
Posts: 629 Likes: 1
Sidelock
|
Sidelock
Joined: May 2006
Posts: 629 Likes: 1 |
Cody:
As for filing the breech, you could try protecting the barrels with a layer of stainless steel heat treat foil. It is about .002" thich and pretty tough. A layer of foil glued to the barrel along with careful work should get it done without serious bloodshed.
The straight rifled barrels are pretty cool. You might try lapping the bores and see how they clean up. Nothing to loose, as you can always ream and polish later.
Glenn
There is no sacrifice too great for someone else to make.
|
|
|
|
Joined: Dec 2005
Posts: 211
Member
|
OP
Member
Joined: Dec 2005
Posts: 211 |
COOL!!!!, where can some of this foil be obtained??? I agree on the rifleing. Anyone have any experience shooting shot with straight rifleing????
Tact is for those not clever enough to be sarcastic
|
|
|
|
Joined: Sep 2006
Posts: 194
Sidelock
|
Sidelock
Joined: Sep 2006
Posts: 194 |
I believe Brownell's carries the foil.
LCSMITH
|
|
|
|
Joined: Sep 2005
Posts: 200
Sidelock
|
Sidelock
Joined: Sep 2005
Posts: 200 |
COOL!!!! Anyone have any experience shooting shot with straight rifleing???? Briley's most expensive full-length fitted sub-gauge tubes come with straight "rifling" (that term always struck me as odd; I thought "rifling", by definition, was spiral, not straight), so it must work pretty well (or at least it does no harm).
|
|
|
|
Joined: May 2006
Posts: 629 Likes: 1
Sidelock
|
Sidelock
Joined: May 2006
Posts: 629 Likes: 1 |
Cody:
The SS foil is expensive because you have to buy a roll of it. If you write to me direct I can send you enough to do the job. BTW, for anybody who might handle this stuff, the cut edges are razor sharp. Nasty stuff. Think about the pretty coiled wire on top of the fences at the local Correctional Facility.
As for the straight rifling, I read about it being experimented with in modern shotguns as an attempt to tighten patterns. Apparently the thinking was that the polishing marks in the barrel tended to spin the shot charge, which would be a Bad Thing for patterns.
In this case I expect the idea was more about fouling management. There is a school of thought that rifling was developed in just such a manner. Someone came up with the idea of a grooved barrel to make loading easier, and then someone else made the leap to spiral grooves and we had the first rifle.
Glenn
gfewless@tds.net
There is no sacrifice too great for someone else to make.
|
|
|
|
Joined: Jan 2006
Posts: 9,433 Likes: 316
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 9,433 Likes: 316 |
Neat Cody! May I add that pic to the 'Damascus Barrels' PictureTrail?
|
|
|
|
Joined: Dec 2005
Posts: 211
Member
|
OP
Member
Joined: Dec 2005
Posts: 211 |
Neat Cody! May I add that pic to the 'Damascus Barrels' PictureTrail? Absolutely
Tact is for those not clever enough to be sarcastic
|
|
|
|
Joined: Jan 2006
Posts: 9,433 Likes: 316
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 9,433 Likes: 316 |
Thanks Cody-the pic is up http://www.picturetrail.com/gallery.fcgi?p=999&gid=16082038Is there a maker's name on the barrels? (BTW:my PM STILL doesn't work )
Last edited by revdocdrew; 07/20/07 10:37 PM.
|
|
|
|
Joined: Jan 2006
Posts: 15,456 Likes: 86
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 15,456 Likes: 86 |
I'd like to hear more about the gun....pics of the bores and gun would be nice.
|
|
|
|
|
|