doublegunshop.com - home Forums General Discussion DoubleGun BBS @ doublegunshop.com Creating the "jeweling" or "engine turning" finish

October
S	M	T	W	T	F	S
			1	2	3	4
5	6	7	8	9	10	11
12	13	14	15	16	17	18
19	20	21	22	23	24	25
26	27	28	29	30	31

Who's Online Now

7 members (Carcano, obsessed-with-doubles, canvasback, FlyChamps, 2 invisible), 491 guests, and 4 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums10

Topics39,493

Posts562,054

Members14,585

Most Online9,918
Jul 28th, 2025

Print Thread

Re: Creating the "jeweling" or "engine turning" finish gil russell #304008 12/11/12 10:40 PM
Joined: Nov 2006 Posts: 3,475 Likes: 54 Replacement Sidelock
Replacement Sidelock Joined: Nov 2006 Posts: 3,475 Likes: 54	Way back in the 60's, we did parts with an ink eraser in a drill press or a mill. The quality of erasers has probably changed since then.

Entire Thread
Subject	Posted By	Posted
Creating the "jeweling" or "engine turning" finish	gil russell	12/12/12 02:02 AM
Re: Creating the "jeweling" or "engine turning" finish	skeettx	12/12/12 02:09 AM
Re: Creating the "jeweling" or "engine turning" finish	J.R.B.	12/12/12 02:09 AM
Re: Creating the "jeweling" or "engine turning" finish	Rocketman	12/12/12 02:37 AM
Re: Creating the "jeweling" or "engine turning" finish	Replacement	12/12/12 02:40 AM
Re: Creating the "jeweling" or "engine turning" finish	mike campbell	12/12/12 03:54 AM
Re: Creating the "jeweling" or "engine turning" finish	Salopian	12/12/12 08:06 AM
Re: Creating the "jeweling" or "engine turning" finish	J.R.B.	12/12/12 12:48 PM
Re: Creating the "jeweling" or "engine turning" finish	Pugwash	12/12/12 08:20 AM
Re: Creating the "jeweling" or "engine turning" finish	Claybird	12/12/12 11:42 AM
Re: Creating the "jeweling" or "engine turning" finish	Chuck H	12/12/12 01:17 PM
Re: Creating the "jeweling" or "engine turning" finish	Gnomon	12/12/12 02:26 PM
Re: Creating the "jeweling" or "engine turning" finish	J.R.B.	12/12/12 02:59 PM
Re: Creating the "jeweling" or "engine turning" finish	Gnomon	12/12/12 08:14 PM
Re: Creating the "jeweling" or "engine turning" finish	Chuck H	12/12/12 03:48 PM
Re: Creating the "jeweling" or "engine turning" finish	Daryl Hallquist	12/12/12 03:55 PM
Re: Creating the "jeweling" or "engine turning" finish	TwiceBarrel	12/12/12 04:16 PM
Re: Creating the "jeweling" or "engine turning" finish	dave1	12/12/12 05:18 PM
Re: Creating the "jeweling" or "engine turning" finish	Ithaca5E	12/12/12 10:11 PM

Link Copied to Clipboard

Updated every minute of everyday!

Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 3.336s Queries: 17 (0.476s) Memory: 0.8288 MB (Peak: 1.9024 MB) Data Comp: Off Server Time: 2025-10-07 22:16:16 UTC
Valid HTML 5 and Valid CSS