|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
|
|
|
1
|
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
|
30
|
31
|
|
|
|
|
|
|
|
3 members (SKB, Hammergun, 1 invisible),
1,139
guests, and
6
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums10
Topics40,344
Posts574,155
Members14,700
| |
Most Online32,084
Jun 14th, 2026
|
|
|
|
Joined: Dec 2006
Posts: 3,365 Likes: 440
Sidelock
|
OP
Sidelock
Joined: Dec 2006
Posts: 3,365 Likes: 440 |
Hi all, say just a quick question. For those of you who own a Skeets bore gauge (the dail type not the digital) how accurate is it?
Thanks so much!!!!
Greg
Gregory J. Westberg
MSG, USA
Ret
|
|
|
|
|
Joined: May 2004
Posts: 790 Likes: 47
Sidelock
|
|
Sidelock
Joined: May 2004
Posts: 790 Likes: 47 |
It is as accurate as the setting ring that you use.
|
|
|
|
|
Joined: Oct 2007
Posts: 496
Sidelock
|
|
Sidelock
Joined: Oct 2007
Posts: 496 |
gjw:
It's as accurate as I need such a gauge to be. And you don't even have to use the setting rings to merely measure choke in most instances... just watch the dial and note how many thou the constriction is as you pull the gauge out.
|
|
|
|
|
Joined: Dec 2001
Posts: 3,977 Likes: 110
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 3,977 Likes: 110 |
I've used one for years and have crosschecked it with other more expensive units. Very close results.
Disagreement is one of the joys of freedom.
|
|
|
|
|
Joined: Apr 2002
Posts: 6,812
Sidelock
|
|
Sidelock
Joined: Apr 2002
Posts: 6,812 |
Be careful you don't get the balls all schwetty as they have a tendency to stick occasionally. And Kensal is correct that the difference bore to choke doesn't require zeroing to .700" ring or what have you. I'd prefer a Stan Baker all gauge set but I'd also like to have a condo at the beach and a 125' yacht with crew and waitstaff.
jack
|
|
|
|
|
Joined: Jan 2002
Posts: 11,575 Likes: 182
Sidelock
|
|
Sidelock
Joined: Jan 2002
Posts: 11,575 Likes: 182 |
I've used one for years and have crosschecked it with other more expensive units. Very close results. Ditto.
|
|
|
|
|
Joined: Feb 2006
Posts: 3,863 Likes: 124
Sidelock
|
|
Sidelock
Joined: Feb 2006
Posts: 3,863 Likes: 124 |
I bought one years ago on eBay for $15.00. It was in a homemade wooden case and looked good. Trouble is, someone took it apart and put it back wrong, the had the spring on the wrong side. I fiddled with it and got it to work and it will give you re-peatable readings.
I called them and wanted a ten gage head, the fellow told me to adjust the phenolic tube farther down to allow the balls to travel farther. It still isn't enough for .775 or larger for earlier 10 ga bores.
For the money they are good, if I had the money I would get the 100 Straight with the 4 heads for $500.00
David
|
|
|
|
|
Joined: Jan 2002
Posts: 14,674 Likes: 2438
Sidelock
|
|
Sidelock
Joined: Jan 2002
Posts: 14,674 Likes: 2438 |
Mine has done me a good job for several years. Since it is not used constantly I re-zero with the setting ring every use. Only takes a few seconds.
SRH
May God bless America and those who defend her.
|
|
|
|
|
Joined: Feb 2002
Posts: 14,649 Likes: 346
Sidelock
|
|
Sidelock
Joined: Feb 2002
Posts: 14,649 Likes: 346 |
Of course you zero it every use. Another tip is to make sure the shaft runs free. After fifteen years or so, I had to put a drop or two of thin oil on the micrometer shaft. The balls stick a bit, but I'm not sure I should oil them.
|
|
|
|
|
Joined: Jul 2005
Posts: 2,444 Likes: 42
Sidelock
|
|
Sidelock
Joined: Jul 2005
Posts: 2,444 Likes: 42 |
I tested one against Galazans and could detect no discernible difference in measurement.
|
|
|
|
|
|
|
