|
S |
M |
T |
W |
T |
F |
S |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
|
Forums10
Topics38,900
Posts550,586
Members14,458
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Apr 2011
Posts: 610
Sidelock
|
Sidelock
Joined: Apr 2011
Posts: 610 |
I once had a Sauer that was hard to open after firing. The extractors did not have full free travel; starting to get tight just before seating in the breech recess.
Filed the ends of the extractors and worked fine. Too tight a fit;; needed more clearance.
Last edited by 2holer; 09/11/11 06:47 PM.
|
|
|
|
Joined: Dec 2001
Posts: 3,553
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 3,553 |
Gene..is that you 3 grains over max plus a different shellcase load ? franc
Last edited by Franc Otte; 09/11/11 08:50 PM.
|
|
|
|
Joined: Jan 2002
Posts: 2,522
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 2,522 |
Before you get too involved in mechanical reasons the gun is hard to open, clean the chambers really well. Use some scotch brite on the end of your cleaning tool along with some solvent/oil and really scour it clean. I have cured two doubles of really stiff opening problems with nothing more. If the chambers are not clean it is possible for them to retain the hulls requiring quite a bit of leverage to get the gun open. Also cured a couple of semi autos which wouldn't properly function the same way.
|
|
|
|
Joined: Jan 2006
Posts: 15,457 Likes: 88
Sidelock
|
Sidelock
Joined: Jan 2006
Posts: 15,457 Likes: 88 |
First thing I'd do would be to look at my ammo.
|
|
|
|
Joined: Feb 2011
Posts: 1,405
Sidelock
|
Sidelock
Joined: Feb 2011
Posts: 1,405 |
The Stevens doubles are pretty simple and if it opens fine before fired, then it should open fine after firing (in theory). If the pins are not sticking in the primers, then you can rule that out.
Another thing to check would be if it is in fact the cocking mechanism. The Stevens 5100 (311) cocks by the barrels lifting an arm in the base of the action. What I would do is uncock it (by dry firing it against a block of wood as to not chance breaking the pins), and then assemble the gun and open it (to cock it) without anything in the chambers. If it opens fine at that time, then the issue is related to the shells being in the chambers.
What type of ammo are you using? I have found that some of the cheap Winchester target loads (from walmart) what to expand the matal base when fired and make them stick up in the chambers of some guns. This also loosens the metal base on the shell as well. I have had some guns where I cannot put a fired shell back into the chamber due to the expansion of the shell base. I also once had an ejector single shot that would not eject the shell due to this issue as well. Talk about a pain in the ass at the trap range...
B.Dudley
|
|
|
|
Joined: Jan 2010
Posts: 683
Sidelock
|
OP
Sidelock
Joined: Jan 2010
Posts: 683 |
Thanks to all who responded. The shotgun will indeed open, it's not locked, but it's difficult to fully open it.
I'm using Fiochi hulls with 16.5 gr. of Green Dot.
|
|
|
|
Joined: Jan 2002
Posts: 3,774 Likes: 1
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 3,774 Likes: 1 |
First thing I'd do would be to look at my ammo. Me too. It could be ejector-extractor wear. In this case it's possible to see some tracks/swellings on hull cooper.
Geno.
|
|
|
|
Joined: Jan 2002
Posts: 7,715 Likes: 114
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 7,715 Likes: 114 |
Thanks to all who responded. The shotgun will indeed open, it's not locked, but it's difficult to fully open it. Genelang, you may be talking about the built in limit in the gape of the 311 which is there on purpose to prevent your shells from falling out when you carry it open. That's a pretty handy feature IMHO, and I wouldn't try to change it. There is a way to do something with the cocking rods to allow the 311 to gape fully open...Geo
|
|
|
|
|
|