|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
|
2 members (LGF, 1 invisible),
853
guests, and
3
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums10
Topics39,528
Posts562,457
Members14,592
| |
Most Online9,918
Jul 28th, 2025
|
|
|
|
Joined: Dec 2001
Posts: 447
Sidelock
|
OP
Sidelock
Joined: Dec 2001
Posts: 447 |
Will modern Krieghoff K32 barrels fit my old Remington model 32 (not 3200)? I'm looking for a set of 30" or longer barrels.
Last edited by hoser; 09/28/10 02:32 AM.
|
|
|
|
|
Joined: Oct 2006
Posts: 879
Sidelock
|
|
Sidelock
Joined: Oct 2006
Posts: 879 |
"Modern K32?" The K32 hasn't been made for many years (30?) I would assume that any K32 barrels would fit the Remington. Not sure about K80 barrels.
|
|
|
|
|
Joined: Feb 2002
Posts: 14,457 Likes: 278
Sidelock
|
|
Sidelock
Joined: Feb 2002
Posts: 14,457 Likes: 278 |
I have seen Remington and Krieghoff barrels switched, but I don't know what changes have to be made to do it.
|
|
|
|
|
Joined: Dec 2001
Posts: 2,961 Likes: 9
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 2,961 Likes: 9 |
K-80 and K-32 barrels swap, but quite often the rotation area is worn and must be renewed. We have trap shooters that claim the K32 barrrels shoot better patterns.
bill
|
|
|
|
|
Joined: Feb 2002
Posts: 14,457 Likes: 278
Sidelock
|
|
Sidelock
Joined: Feb 2002
Posts: 14,457 Likes: 278 |
Bill, your answer is interesting, but a little off topic. The poster is asking about Remingtons.
|
|
|
|
|
Joined: Dec 2001
Posts: 6,462 Likes: 344
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 6,462 Likes: 344 |
bill S., your K-80 and K-32 barrel info. is interesting. I assume that you think it possible the K-80 barrels might adapt to the Remington Mod. 32. Is this your thought ?
Last edited by Daryl Hallquist; 09/28/10 08:03 PM.
|
|
|
|
|
Joined: Jan 2002
Posts: 2,522
Sidelock
|
|
Sidelock
Joined: Jan 2002
Posts: 2,522 |
K80 barrels have to be fitted, but they will go on a K-32. Because the Kriehoff's used the Remington blueprints and a couple Rem Mod 32s as models for their initial production I would think either K32 or K80 barrels might be fitted to the Rem 32 but you are going to have to account for wear and a minimum dimension Kreighoff probably will not work out well with a maximum dimension Rem without some metal work. When I had new K32 barrels added to my K32 they required fitting too so they will not be just drop ins. And because I had an early version the top latch had to be replaced and fitted as well.
Last edited by Jerry V Lape; 09/28/10 08:16 PM.
|
|
|
|
|
Joined: Dec 2001
Posts: 2,961 Likes: 9
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 2,961 Likes: 9 |
Kreighoff in PA has the ability to silver solder inserts on the rotating half rounds on the K gun barrels, they then remachine them to factory specs. Could they fit a K barrel to an old 32, sure. Would they do it? I doubt it and the cost was $400 a few years ago. I would go to Simmons who has made barrels for both guns. I believe that they have the same skill sets and are open to more general jobs at a more realistic cost. I have been looking for a set of K-80-32 thirty inch screw choke barrels and can't find any under $2000, so get ready to spend some big bucks.
bill
|
|
|
|
|
|
|
