|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
|
0 members (),
642
guests, and
5
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums10
Topics39,540
Posts562,549
Members14,592
| |
Most Online9,918
Jul 28th, 2025
|
|
|
|
Joined: Nov 2005
Posts: 4,598
Sidelock
|
Sidelock
Joined: Nov 2005
Posts: 4,598 |
Taking the bulge out of those laminated barrels can be done. They will be a little "tender" in that area. As long as you are careful, it should be OK.
Pete
|
|
|
|
|
Joined: Dec 2001
Posts: 2,961 Likes: 9
Sidelock
|
|
Sidelock
Joined: Dec 2001
Posts: 2,961 Likes: 9 |
I like it, I would start by taking off the brass patch and soaking the parts to remove the oil, I would also wash the stock with alcohol. At that point it may be possible to epoxy the wood together. The toe chip is easy, just plane it off and transplant a new piece of wood with epoxy and form it.. I would also work to stop any barrel rust NOW. A minimum of a strong WD40 spray and then polish, if a lot of polishing is required inside and out it may be a good idea to check wall thickness.
bill
|
|
|
|
|
Joined: Sep 2006
Posts: 157 Likes: 2
Sidelock
|
|
OP
Sidelock
Joined: Sep 2006
Posts: 157 Likes: 2 |
I like it, I would start by taking off the brass patch and soaking the parts to remove the oil, I would also wash the stock with alcohol. At that point it may be possible to epoxy the wood together. The toe chip is easy, just plane it off and transplant a new piece of wood with epoxy and form it.. I would also work to stop any barrel rust NOW. A minimum of a strong WD40 spray and then polish, if a lot of polishing is required inside and out it may be a good idea to check wall thickness.
bill No active rust I can find, except a tad on the tip of the right barrel tip at the ding, but it has been well oiled. I can do some of the stock work, but will probably send it to the guy who has done other stock work for me. I can check the wall thickness at the breech and muzzle with my micrometer. Is that enough? If not, how is it done?
|
|
|
|
|
Joined: Nov 2006
Posts: 3,477 Likes: 54
Sidelock
|
|
Sidelock
Joined: Nov 2006
Posts: 3,477 Likes: 54 |
Bill, looks to me like the brass plates are mortised into the top of the stock wrist. Would be pretty difficult to lay in a pair of patches to fill those and still blend them. Might be doable with a fair amount of faux graining, though.
|
|
|
|
|
Joined: Sep 2006
Posts: 157 Likes: 2
Sidelock
|
|
OP
Sidelock
Joined: Sep 2006
Posts: 157 Likes: 2 |
Actually, my plan is to have the stock repaired and recheckered, but leave the brass plates and engrave them. I think it will add character to the piece and they are pat of the gun's history.
|
|
|
|
|
Joined: Sep 2006
Posts: 157 Likes: 2
Sidelock
|
|
OP
Sidelock
Joined: Sep 2006
Posts: 157 Likes: 2 |
Actually, my plan is to have the stock repaired and recheckered, but leave the brass plates and engrave them. I think it will add character to the piece and they are part of the gun's history.
Last edited by Rudybollo; 12/16/08 10:25 PM.
|
|
|
|
|
Joined: May 2007
Posts: 605 Likes: 1
Sidelock
|
|
Sidelock
Joined: May 2007
Posts: 605 Likes: 1 |
muzzle (where chokes might be) and breech are not the places to measure wall thickness; ideally, you want to know all the way along the barrels, and ideally, you really want to know that it's thick enough where your leading/non-master hand is. Wall thickness gauge is the tool for that job, not a pair of calipers.
RG
|
|
|
|
|
|
|
