|
S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
6 members (SKB, bushveld, 4 invisible),
219
guests, and
3
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,463
Posts545,052
Members14,409
|
Most Online1,258 Mar 29th, 2024
|
|
|
Joined: Dec 2004
Posts: 108
Sidelock
|
OP
Sidelock
Joined: Dec 2004
Posts: 108 |
I Have a barrel loose 21 Winchester((0ff face)) That tightens right up with a .006 shim in the barrel hook. I was planing on using a .005 or .006 feeler gauge for the shim. Is their some other material that would work better??? The last one of these that I did was 30 + Yrs. ago. I used Brownells Acraglas to hold shim in place. I sold that gun a few years later and the shim was then still in place and working well. I am now a little old, and maybe behind the curve, so all suggestions and advice be appreciated. David
|
|
|
|
Joined: Jan 2013
Posts: 1,124 Likes: 195
Sidelock
|
Sidelock
Joined: Jan 2013
Posts: 1,124 Likes: 195 |
Good quality feeler gauge steel I feel cant be bettered for the cost, the nature of the beast makes the thickness sizing accurate too. Holding it in place I have always used wood's metal solder.
The only lessons in my life I truly did learn from where the ones I paid for!
|
|
|
|
Joined: Jan 2002
Posts: 7,702 Likes: 99
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 7,702 Likes: 99 |
I don't know what material is best, but I use sticky backed air conditioner metal tape. Just degrease, cut tape to fit and apply. I haven't had the repair go bad on anything I've used it on yet...Geo
|
|
|
|
Joined: Feb 2002
Posts: 1,850 Likes: 150
Sidelock
|
Sidelock
Joined: Feb 2002
Posts: 1,850 Likes: 150 |
I've always used 'shim stock', a packet of various steel shim stock in sizes running from .002 up to something like .035. The pieces are about 4"x 6" each and ink stamped to ID the thickness.
Gives you a lot of matrl if you do a lot of different shop work.
Raiding an old feeler gauge for a piece of suitable thickness is the other way and you don't get stuck with a book of shim stock you'll never use.
I've always soft soldered the shim into place. Tin the shim stock. Clean the hook well. I scrape them clean.
Flux both surfaces and clamp the shim in tight with a piece of round stock. Get in there with some heat to flow the solder and add a touch when it flows. Tweak the clamp a touch tighter and let it cool. No, the ribs won't fly off. But if you feel better clamping the upper rib to the short rib below,,do so. File off the excess and polish up the lugs.
I know gluing things into place is the way lately, but for most things of this nature I just haven't wandered out into that brave new world yet.
|
|
|
|
|
|