|
S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums10
Topics38,479
Posts545,210
Members14,410
|
Most Online1,335 Apr 27th, 2024
|
|
|
Joined: Oct 2010
Posts: 150 Likes: 2
Sidelock
|
OP
Sidelock
Joined: Oct 2010
Posts: 150 Likes: 2 |
I have a shotgun with too much drop at comb and need it bent. I'm in N. Illinois. Who can bend this stock and make it fit me better?
|
|
|
|
Joined: Feb 2002
Posts: 1,558 Likes: 22
Sidelock
|
Sidelock
Joined: Feb 2002
Posts: 1,558 Likes: 22 |
I'd check with FieldSport in Traverse City. They will probably recommend Dale Witman. https://www.facebook.com/FIELDSPORTLTD/
foxes rule
|
|
|
|
Joined: Jan 2009
Posts: 768 Likes: 19
Sidelock
|
Sidelock
Joined: Jan 2009
Posts: 768 Likes: 19 |
Mike Orlen in MA. His price list is on the Shotgun World site, under gunsmithing.
good luck
|
|
|
|
Joined: Oct 2004
Posts: 1,826 Likes: 12
Sidelock
|
Sidelock
Joined: Oct 2004
Posts: 1,826 Likes: 12 |
Get a couple of heat lamps and a old sock soaked in cooking oil you can tie on the wrist. Make sure all screws are tight and let the stock hang over the edge of a table. Put a bag or two of shot on the barrels and one or sometimes two on the butt of the gun. Measure to the ground and when it gets to where you want it turn off the lamps. If it don't want to bend you're only out a little bit. You won't crack em this way. Good luck. Paul
|
|
|
|
Joined: Oct 2006
Posts: 532 Likes: 1
Sidelock
|
Sidelock
Joined: Oct 2006
Posts: 532 Likes: 1 |
Bending up is more problematic than bending to change the cast. Safari Outfitters in my area (NYS) has someone who skillfully uses the heat and oil method and has corrected the cast for me on several guns and raised the comb a bit on a couple of guns, although that is trickier.
Rich
|
|
|
|
Joined: Jan 2002
Posts: 5,088 Likes: 36
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 5,088 Likes: 36 |
What type of gun is it? SxS? O/U? Through bolt?
My problem lies in reconciling my gross habits with my net income. - Errol Flynn
|
|
|
|
Joined: Oct 2010
Posts: 150 Likes: 2
Sidelock
|
OP
Sidelock
Joined: Oct 2010
Posts: 150 Likes: 2 |
|
|
|
|
Joined: Oct 2004
Posts: 1,826 Likes: 12
Sidelock
|
Sidelock
Joined: Oct 2004
Posts: 1,826 Likes: 12 |
No through bolt. I use two heat lamps and tin fixtures with clamps bought from Home Depot and a old sock dipped in cooking oil wrapped around the wrist. A old shoe lace holds it in place. After making sure all screws are tight the gun is laid on a bench with the stock over the side. Put a couple of bags of shot, or something heavy, and do the same on the end of the stock. Measure down to the floor, and every half hour check it. When it bends to what you want, or a bit more to guard against spring back, turn off the lights. Wait a bit, say a hour and remove the weight on the stock and see if it stays. You can't hurt anything this way. It doesn't cost much. Now if you were bending down you'd have to make sure the grain of the wood didn't run out along the top of the wrist. Same with cast. But even with them you're not forcing anything to happen. It will only bend if it wants to. I've cracked a couple using a fixture with a threaded rod and nut. I'd just turn a nut and it would move the stock the way I wanted with a nylon strap around the stock. I went to this way and never cracked another one.
|
|
|
|
Joined: Jan 2004
Posts: 6,715 Likes: 415
Sidelock
|
Sidelock
Joined: Jan 2004
Posts: 6,715 Likes: 415 |
Paul, I like your built in method of moderation in bending. I know I was pushing my first one too hard at the beginning because I did not realize how soft and flexible it would get. I got away with it but your way is safer, especially the first time.
I like to wait overnight for the stock to set before removing the force.
_________ BrentD, (Professor - just for Stan)
|
|
|
|
|
|