March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Who's Online Now
1 members (Travis S), 251 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums10
Topics38,373
Posts543,976
Members14,389
Most Online1,131
Jan 21st, 2024
Previous Thread
Next Thread
Print Thread
#525994 10/13/18 12:05 PM
Joined: Jun 2017
Posts: 8
JR1948 Offline OP
Boxlock
OP Offline
Boxlock

Joined: Jun 2017
Posts: 8
Hi All,
Firstly, I just refinished a "not-so-old" Sarasqueta, and it turned out just Ok. But, before I finished it, I was browsing the aisles at ye olde hardware store and found this Minwax product.

My question is, does anyone have experience with this stuff? The instructions on the can say it is s'posed to penetrate and seal the end-grain, but it did not. About all it did, was put a shiny, gloss finish on the inletting. (Not very thick, it went back together easily).


Personally, I have a low regard for Minwax products in general, but this stuff just looked like a good thing. Then again, maybe I'm just behind the curve, and ya'll already have opinions, good or bad, about it ?


Take care,

JR

Joined: Feb 2011
Posts: 1,405
Sidelock
**
Offline
Sidelock
**

Joined: Feb 2011
Posts: 1,405
Never heard of the stuff, but it sounds like it did not do what you hoped it to. Yes, Minwax is more of a home center/consumer brand these days and hardly used by professionals.


B.Dudley
Joined: Feb 2002
Posts: 1,850
Likes: 150
Sidelock
***
Offline
Sidelock
***

Joined: Feb 2002
Posts: 1,850
Likes: 150
The Minwax stuff most of the the other DIY store wood saver products are about 70%+ acetone,,a small % of alcohol and the rest are the solids in it (25% or so) that are an acrylic.

The solid is dissolved in the acetone. The acetone when applied to the end grain or to less than stable wood (dry rot, punky, ect),,it soaks in fast and in most instances fairly deep.
The acrylic disolved in it is carried with it,,then the acetone and alcohol evaporate at a rapid rate even from deep in the wood.
What is left is that acrylic plastic in solid form interlaced within the wood to reinforce it.

Works pretty good on old window sills and stuff like that where you can end up pouring nearly the entire can or bottle onto and into one bad spot. It soaks deep into soft dryrot stuff like that.

Some wood workers that make decorative projects use the same idea to stabilize wood blanks before use in turning and other machined wood projects.
They sometimes employ vacuum pumps get the stuff to fully enter the wood pieces or sometimes let them soak for days in it.

The home-made soln of the commercial mix is the same acetone and alcohol with common plexiglass bits disolved in it.
I've read of some use of hard styrofoam in place of the plexiglass. I don't know if it's the same stuff (acrylic?,,plastic?)but the people claim it works the same. I'm no chemist, so I don't know.

Same idea,,introduce a strong stable solid into solution so you can get it into the wood.

Soaking or vacuum pumping a gun stock full of the stuff probably wouldn't be too good,,might be a weight problem (?),,seems like it would end up being your wood finish if it was saturated with the stuff.
But soaked into the end grain seems like an OK thing.

I'd think one of the ultra thin SuperGlues applied to the end grain might do the same thing with a whole lot less drama though.

Joined: Jan 2002
Posts: 13,126
Likes: 1126
Sidelock
**
Offline
Sidelock
**

Joined: Jan 2002
Posts: 13,126
Likes: 1126
I agree with Brian. Minwax is not the first choice of most pros, but for an amateur like me they can be worthwhile . See this post about a previous experience.

http://forum.foxcollectors.com/viewtopic.php?f=15&t=7229

SRH


May God bless America and those who defend her.
Joined: Jun 2017
Posts: 8
JR1948 Offline OP
Boxlock
OP Offline
Boxlock

Joined: Jun 2017
Posts: 8
Thanks for the replies friends,

Nebody wanna buy an "almost full" can of Wood Hardener ?


Stan, that's nice work - I've had a few that turned out that good, but not often ! Monty Kennedy would be proud of that checkering.


Kutter, I agree - the Superglues are the best product we have available. I thought, for an instant, that I was gonna save a few bucks …. C'est la vie'


Take care, everyone


JR

Joined: Jan 2002
Posts: 13,126
Likes: 1126
Sidelock
**
Offline
Sidelock
**

Joined: Jan 2002
Posts: 13,126
Likes: 1126
Sorry if I didn't make it clear about the Minwax products...........it was that brand stains that I used on the Fox to match the f/end.

Tootle oooo, SRH


May God bless America and those who defend her.

Link Copied to Clipboard

doublegunshop.com home | Welcome | Sponsors & Advertisers | DoubleGun Rack | Doublegun Book Rack

Order or request info | Other Useful Information

Updated every minute of everyday!


Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 0.057s Queries: 26 (0.037s) Memory: 0.8122 MB (Peak: 1.8988 MB) Data Comp: Off Server Time: 2024-03-28 08:45:35 UTC
Valid HTML 5 and Valid CSS