|
S |
M |
T |
W |
T |
F |
S |
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
1 members (Marplot),
1,173
guests, and
6
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,445
Posts544,841
Members14,406
|
Most Online1,258 Mar 29th, 2024
|
|
|
Joined: Aug 2013
Posts: 973 Likes: 23
Sidelock
|
OP
Sidelock
Joined: Aug 2013
Posts: 973 Likes: 23 |
What's the likelihood of a stock being able to be straightened once it's been bent? Specifically, a bend good for a left handed shooter being straightened back to neutral.
Thanks.
|
|
|
|
Joined: Jan 2004
Posts: 6,703 Likes: 406
Sidelock
|
Sidelock
Joined: Jan 2004
Posts: 6,703 Likes: 406 |
Pretty good. It's a stock that has already proven it can be bent. I would have no extra concerns about it.
_________ BrentD, (Professor - just for Stan)
|
|
|
|
Joined: Aug 2013
Posts: 973 Likes: 23
Sidelock
|
OP
Sidelock
Joined: Aug 2013
Posts: 973 Likes: 23 |
Pretty good. It's a stock that has already proven it can be bent. I would have no extra concerns about it. Thanks. I've seen some nice guns for very low prices because they are only appropriate for a very narrow market. If the bends can be reversed without too much trouble or cost, then the gun is more viable for more shooters.
|
|
|
|
Joined: Aug 2013
Posts: 973 Likes: 23
Sidelock
|
OP
Sidelock
Joined: Aug 2013
Posts: 973 Likes: 23 |
Related question, who do folks typically turn to for a stock bending procedure?
|
|
|
|
Joined: Jul 2012
Posts: 4,461 Likes: 207
Sidelock
|
Sidelock
Joined: Jul 2012
Posts: 4,461 Likes: 207 |
B.Graham, The stock can still likely be bent, but original "cast on" likely came from original stock layout, not a previous bending. Mike
|
|
|
|
Joined: Dec 2011
Posts: 908 Likes: 43
Sidelock
|
Sidelock
Joined: Dec 2011
Posts: 908 Likes: 43 |
Dan Rositerr at Custom Stocks and Steel is very good.
|
|
|
|
Joined: May 2004
Posts: 2,091 Likes: 13
Sidelock
|
Sidelock
Joined: May 2004
Posts: 2,091 Likes: 13 |
I have bent a cast on for a friend to make it cast off successfuly but you are taking a risk. My experience, at the hobby level, has been that some stocks just don't bend. I have been told by a reputable gun smith that he will leave a difficult gun on the bender for a couple of days under heat to accomplish the task. I have never tried this and I question that it works.
So many guns, so little time!
|
|
|
|
Joined: Jan 2009
Posts: 767 Likes: 19
Sidelock
|
Sidelock
Joined: Jan 2009
Posts: 767 Likes: 19 |
Mike Orlen has bent several for me and others. He modertaes the gunsmithing forum on Shotgun World and has a price list posted.
|
|
|
|
Joined: Jan 2004
Posts: 6,703 Likes: 406
Sidelock
|
Sidelock
Joined: Jan 2004
Posts: 6,703 Likes: 406 |
I've done it myself and with the right piece of wood, I will do it again. I built the jigs and it wasn't too hard. I used some notes that I believe came from Mike Orlen. It was not hard to do.
_________ BrentD, (Professor - just for Stan)
|
|
|
|
Joined: Jan 2002
Posts: 1,478 Likes: 16
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 1,478 Likes: 16 |
I shoot lefty and have had several stocks bent from cast off to cast on. Standard procedure and I am about to have the stock on my Atkin 'adjusted'. I will ask DES to do the work, based on past experience with his work.
C Man Life is short Quit your job. Turn off the TV. Go outside and play.
|
|
|
|
|
|