|
S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums10
Topics38,499
Posts545,465
Members14,414
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Jan 2009
Posts: 768 Likes: 19
Sidelock
|
OP
Sidelock
Joined: Jan 2009
Posts: 768 Likes: 19 |
Is there a chart or formula for converting British tons per square nitro proof into US psi.
thanks
|
|
|
|
Joined: Feb 2002
Posts: 1,851 Likes: 150
Sidelock
|
Sidelock
Joined: Feb 2002
Posts: 1,851 Likes: 150 |
One UK Long Ton = 2240 psi
|
|
|
|
Joined: Jun 2008
Posts: 2,737 Likes: 96
Sidelock
|
Sidelock
Joined: Jun 2008
Posts: 2,737 Likes: 96 |
I don't think there is an exact formula as they are measured differently. Roughly 8,500 psi is thought to be around the same as 3 tons per square inch pressure rating and 9,000 for 2 3/4 inch 3 1/4 tons per square inch. That is as far as I am aware unless someone else has a more exact idea. Lagopus.....
|
|
|
|
Joined: Feb 2008
Posts: 11,344 Likes: 390
Sidelock
|
Sidelock
Joined: Feb 2008
Posts: 11,344 Likes: 390 |
According to the 1954 British Rules of Proof, 3 tons = 8,938 psi 3 1/4 tons = 9,682 psi 3 1/2 tons = 10,427 psi 4 tons = 11,917 psi But if you plug those British long ton numbers into a converter like this, the numbers don't come out the same: https://www.convert-me.com/en/convert/pressure/longtoninsq.html?u=longtoninsq&v=3.25The best explanation for the difference that I've seen, when this has been discussed in the past, came from Miller (2-Piper) The Ton used in British proof was 2240lbs. Thus tons x 2240 is a direct conversion from tons to pounds. What is "NOT" a direct conversion is crusher pressures to piezo-electric pressures which are considered to give true PSI. In the early days of working with the piezo-electric pressures bbls were set up with both P-E & crusher gages & simultaneous readings taken at the same 1.0" station. A "Workable" formula for conversion, within the normal pressure range of shotgun bbls was found to be; P-E (tons) = (Crusher tons x 1.5)-.5 Multiplying this figure by 2240 will then give psi. Note that this formula was not given to be "Exact" but to give reasonable working pressures. By working through the pressures given per the Birmingham proof house & comparing the greatest difference will be found to be on the order of 3% & this on the 4ton pressure, the other 3 being from 2% down to near zero. The reason for the differences & why no exact formula can be given is because of the varible "Lag Time" in crushing the piston. Within this range crusher pressures will always read less than the P-E pressures. And this is why we need Miller to get well and stay well!
A true sign of mental illness is any gun owner who would vote for an Anti-Gunner like Joe Biden.
|
|
|
|
Joined: Jan 2009
Posts: 768 Likes: 19
Sidelock
|
OP
Sidelock
Joined: Jan 2009
Posts: 768 Likes: 19 |
thanks all. I purchased a 20 nitro proofed damascus hammer gun with 3 tons per stampings and I did not want to shoot off the shelf high pressure loads. Am I correct in asuming that 3 tons is service load and not definitive pressure, have I got that correct?
John
|
|
|
|
Joined: Dec 2001
Posts: 12,743
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 12,743 |
Note that while the piezo-electric pressures should be interchangeable anywhere as they are true pressure the crusher pressures are not universally interchangeable. The British & the US did not necessarily use the exact same set up for taking crusher pressures, therefore should only be compared to their individual set up. The same load which measured 3 tons (6720 lbs) my well have not read 6720 on an American crusher gauge due to the different set-up. The formula cited was thus good "ONLY" for British crusher pressures, though the conversion to psi would be good for US guns.
Miller/TN I Didn't Say Everything I Said, Yogi Berra
|
|
|
|
Joined: Jun 2008
Posts: 2,737 Likes: 96
Sidelock
|
Sidelock
Joined: Jun 2008
Posts: 2,737 Likes: 96 |
susjwp, yes 3 tons is the service pressure. 'Off the shelf' high pressure loads would not be advisable. Standard British 20 bore 2 1/2" cartridge carries a load of 13/16th. ounce of shot. I would use only CIP approved ammo marked 65mm. or 67mm. Lagopus.....
|
|
|
|
Joined: Jan 2002
Posts: 11,379 Likes: 105
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 11,379 Likes: 105 |
Our British cousins have done their best to confuse us with proofmarks. Even when they converted to metric proofmarks back in the mid to late 80's (850 bar etc), you could not convert that to American psi via a mathematical formula. They were still expressing crusher values in metric figures while we had converted to piezo-electronic.
|
|
|
|
|
|