S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
1 members (1 invisible),
667
guests, and
6
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums10
Topics38,506
Posts545,604
Members14,419
|
Most Online1,344 Apr 29th, 2024
|
|
|
Joined: Jan 2002
Posts: 7,703 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,703 Likes: 103 |
The fore end fell off my Browning Bss Sidelock after ejecting two fired shells. The ejector hammers are in the fired position (rear) protruding above the fore end metal. The position prevents the fore end from being re-attached to the gun because the protruding hammers prevent the fore end iron from fitting far enough into to hinge to allow the barrel lug to fit into the slot.
How do I re-cock them with the fore end off the barrel?...Geo
Last edited by Geo. Newbern; 08/06/17 03:53 PM. Reason: spellin'
|
|
|
|
Joined: Dec 2001
Posts: 6,994 Likes: 402
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 6,994 Likes: 402 |
Geo, hold the fore end in one hand and use a hardwood dowel to push each ejector hammer towards the front(muzzle). One at a time makes the job easier. Best regards, Steve
|
|
|
|
Joined: Jan 2002
Posts: 7,703 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,703 Likes: 103 |
Geo, hold the fore end in one hand and use a hardwood dowel to push each ejector hammer towards the front(muzzle). One at a time makes the job easier. Best regards, Steve Thanks Steve. Not strong enough. How about a thin wrench to provide leverage?...Geo
|
|
|
|
Joined: Dec 2001
Posts: 6,994 Likes: 402
Sidelock
|
Sidelock
Joined: Dec 2001
Posts: 6,994 Likes: 402 |
I often use the edge of a wooden work bench, press straight down using your weight. A single hammer is much easier than both at once. Careful it does not slip off and damage your wood. A wrench would scare me. Steve
|
|
|
|
Joined: Jan 2002
Posts: 1,567 Likes: 71
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 1,567 Likes: 71 |
Try snapping the 4end on the barrels and pushing the ejector plate back one at a time.
|
|
|
|
Joined: Jan 2002
Posts: 7,703 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,703 Likes: 103 |
Many thanks to Steve and Mark for the advice. I got it done as Steve suggested by pushing the ejector hammers back one at a time. I used a brass punch with a stout handle for better control. Stronger than I thought I was...Geo
|
|
|
|
Joined: Jan 2002
Posts: 13,165 Likes: 1155
Sidelock
|
Sidelock
Joined: Jan 2002
Posts: 13,165 Likes: 1155 |
I do it like Steve said on the edge of a workbench. Even though it takes more effort I can usually do both at the same time easier than one at a time on a corner of the bench.
Glad you got it, Geo. Next question is ........... why did the forend fall off?
SRH
May God bless America and those who defend her.
|
|
|
|
Joined: Jan 2002
Posts: 7,703 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,703 Likes: 103 |
Glad you got it, Geo. Next question is ........... why did the forend fall off?
SRH Because I didn't put it on right. While I was working on it yesterday I took out the Anson plunger and cleaned some goop off of it and swabbed out the barrel it fits in. It had been binding and the latch was not retracting over the barrel lug as it should. Smoothed everything out and it works like a champ now. Doves are in big trouble...Geo Yes, when I unscrewed the detente on the end of the plunger, it and the spring hit the wall on the other side of the room. A gun smith i ain't!
Last edited by Geo. Newbern; 08/07/17 07:50 AM. Reason: added final sentence
|
|
|
|
Joined: Jan 2002
Posts: 7,703 Likes: 103
Sidelock
|
OP
Sidelock
Joined: Jan 2002
Posts: 7,703 Likes: 103 |
I do it like Steve said on the edge of a workbench. SRH I tried the edge of my wife's kitchen table. I hope she does not find the little piece I broke off...Geo
|
|
|
|
|