doublegunshop.com - home Forums General Discussion DIY Gunsmithing @ doublegunshop.com Damascus process failing

May
S	M	T	W	T	F	S
			1	2	3	4
5	6	7	8	9	10	11
12	13	14	15	16	17	18
19	20	21	22	23	24	25
26	27	28	29	30	31

Who's Online Now

4 members (Jtplumb, graybeardtmm3, 2 invisible), 321 guests, and 6 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums10

Topics38,554

Posts546,269

Members14,423

Most Online1,344
Apr 29th, 2024

Print Thread

Re: Damascus process failing mark #509974 03/30/18 09:46 AM
Joined: Aug 2013 Posts: 973 Likes: 23 Durham NC Bill Graham OP Sidelock
OP Bill Graham Sidelock Joined: Aug 2013 Posts: 973 Likes: 23 Durham NC	Originally Posted By: mark I use 1 part circuit board etchant to 4-5 parts distilled water. Weaker may be better. I use what's marketed as curcuit board etchant as well, but there seems to be FeCl and then FeCl3. Inconclusive if there is appreciable difference with this use.

Entire Thread
Subject	Posted By	Posted
Damascus process failing	Bill Graham	03/22/18 04:15 PM
Re: Damascus process failing	keith	03/22/18 06:06 PM
Re: Damascus process failing	Kutter	03/22/18 08:02 PM
Re: Damascus process failing	Bill Graham	03/23/18 03:18 PM
Re: Damascus process failing	Bill Graham	03/29/18 12:15 PM
Re: Damascus process failing	SKB	03/29/18 12:30 PM
Re: Damascus process failing	Bill Graham	03/29/18 01:07 PM
Re: Damascus process failing	SKB	03/29/18 01:59 PM
Re: Damascus process failing	Bill Graham	03/29/18 04:11 PM
Re: Damascus process failing	KY Jon	03/29/18 06:48 PM
Re: Damascus process failing	Bill Graham	03/29/18 08:08 PM
Re: Damascus process failing	mark	03/30/18 01:27 AM
Re: Damascus process failing	Bill Graham	03/30/18 01:46 PM
Re: Damascus process failing	mark	03/30/18 03:50 PM
Re: Damascus process failing	james-l	03/30/18 05:13 PM
Re: Damascus process failing	Kutter	03/30/18 08:00 PM
Re: Damascus process failing	Bill Graham	03/30/18 08:10 PM
Re: Damascus process failing	Bill Graham	04/10/18 02:43 PM
Re: Damascus process failing	SKB	04/10/18 02:59 PM
Re: Damascus process failing	builder	04/11/18 12:38 AM
Re: Damascus process failing	Remington40x	04/11/18 01:26 PM
Re: Damascus process failing	Bill Graham	04/11/18 01:35 PM

Link Copied to Clipboard

Updated every minute of everyday!

Copyright (c) 1993 - 2024 doublegunshop.com. All rights reserved. doublegunshop.com - Bloomfield, NY 14469. USA These materials are provided by doublegunshop.com as a service to its customers and may be used for informational purposes only. doublegunshop.com assumes no responsibility for errors or omissions in these materials. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. doublegunshop.com further does not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these materials. doublegunshop.com shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of these materials. doublegunshop.com may make changes to these materials, or to the products described therein, at any time without notice. doublegunshop.com makes no commitment to update the information contained herein. This is a public un-moderated forum participate at your own risk.

Note: The posting of Copyrighted material on this forum is prohibited without prior written consent of the Copyright holder. For specifics on Copyright Law and restrictions refer to: http://www.copyright.gov/laws/ - doublegunshop.com will not monitor nor will they be held liable for copyright violations presented on the BBS which is an open and un-moderated public forum.

Responsive Width:

PHP: 7.0.33-0+deb9u11+hw1 Page Time: 0.402s Queries: 18 (0.372s) Memory: 0.8302 MB (Peak: 1.8994 MB) Data Comp: Off Server Time: 2024-05-25 00:15:53 UTC
Valid HTML 5 and Valid CSS